AFRC Lab · acoustic · simulated, rated to AS/NZS ISO 717.1
Window acoustic calculator
Choose an opening type, a generic frame, the seals, the glass and the window size, and see the sound reduction Rw (C; Ctr) update as you go. Glazing uses the measured laboratory curve where that build has been tested, otherwise AFRC Lab's calibrated glazing model. Frames here are generic: your actual system can rate higher or lower. Use it to compare the noise reduction of acoustic windows and glass before you specify.
Window
Frame
Glazing
Code: glass mm, laminate as glass/interlayer/glass (R = standard PVB, Q = acoustic PVB, e.g. 3/0.38R/3 = 6.38 lam), cavity in brackets with gas (e.g. [12ar]). Example: 6/0.76Q/6[16ar]10.
A screening check against predicted values only. It is not evidence of compliance: see the notes below.
Simulated, not tested. There is no ISO or Australian standard for simulating window sound insulation: the curve is calculated by AFRC Lab's model, and the single-number ratings are then worked out from it in accordance with AS/NZS ISO 717.1.
Ways to lift this window
| Change | Rw (C; Ctr) | Gain | Basis | Meets requirement |
|---|
Secondary glazing (gaps over 40 mm) isn't suggested here: wide cavities need a full modal model of the actual build. Each row changes one thing on the window above and re-runs it. Basis says where the step comes from: a lab test, the calibrated model, or an engineering estimate still waiting on test data.
Listen
Traffic built from individual cars, trucks, a bus and a motorbike driving past (engine, tyres, Doppler, distance), then tuned so its overall spectrum is the ISO 717-1 spectrum the rating uses: the street is spectrum 2 (Ctr), the freeway spectrum 1 (C). Or load your own site recording. Window open plays the outside sound as it arrives at the window. Window closed takes away only what the window stops at each frequency; the room itself is not modelled. Use headphones: the closed levels are true to scale, so they are quiet.
Where the sound gets through (traffic noise, Ctr spectrum)
| Path | Share | 125 Hz | 500 Hz | 2 kHz |
|---|
Share = part of the transmitted traffic noise (A-weighted, ISO 717-1 spectrum 2) that comes through each path. Columns give each path's own sound reduction in dB. The weakest path sets the result: improving a path that carries little sound changes little.
Rate your actual window
This calculator uses generic frames. AFRC Lab models the real system as drawn (every frame section, its seals and the glass) and reports Rw (C; Ctr) for each window in BTW. afrclab.com.au
Report for your file
Creates a dated, self-contained HTML report of this window: inputs, predicted Rw (C; Ctr), the one-third-octave curve, your requirement check, method and disclaimers. Open it in any browser and use Print / Save as PDF.
Notes and disclaimers
- Simulation, not a test. No ISO, EN or Australian standard sets out how to simulate the sound insulation of a window. The sound reduction curve shown is predicted by AFRC Lab's model. Rw, C and Ctr are then calculated from that curve in accordance with AS/NZS ISO 717.1, using the 100–3150 Hz range. They are not measured values and are not a substitute for a laboratory test report to AS 1191 / ISO 10140.
- Laboratory (product) rating, not on-site performance. Results represent the window as it would perform in a test laboratory. Performance on site (for example D2m,nT,w or DnT,w) is usually lower and depends on installation, the wall, flanking paths, room size and finishes, and workmanship. This tool does not predict internal noise levels and does not assess against AS/NZS 2107.
- Generic frames. Frame types are generic: typical widths and surface masses for each frame material and opening type. They do not represent any specific product. A real system can rate higher or lower, sometimes by several dB.
- Accuracy. The ± value shown comes from a blind check against independent laboratory tests of the same opening type. Individual results can fall outside it. Repeat laboratory tests of the same window typically differ by about 1 dB.
- Seals. Seal options marked "lab tested" are based on laboratory measurements. Those marked "estimate" are engineering estimates awaiting test data. Seals are assumed new, correctly adjusted and closed as tested. Worn, damaged or poorly adjusted seals, and gaps in glazing beads, can reduce performance substantially and are not modelled.
- Installation. The frame-to-wall joint is assumed to be sealed as in a laboratory test. Poorly sealed installation joints, sub-sills and reveal gaps can dominate the result and are not included.
- Glass. Thicknesses are nominal. Laminate interlayers use typical standard or acoustic PVB properties. Toughened and heat-strengthened glass is treated like annealed glass of the same thickness, and coatings are ignored. Builds that match a tested build use the measured laboratory curve; other builds are modelled.
- Wide cavities. Secondary glazing and double windows with cavities over 40 mm are indicative only. Their performance depends strongly on the cavity, its absorption and how the two frames are connected, and needs a full model of the actual build.
- Window size. The model is calibrated mainly on laboratory-sized specimens of about 1.2–1.5 m. Very large, very small or unusually proportioned windows are less certain.
- Requirement check. The pass, borderline and fail indicators compare predicted values with the numbers you enter. They do not demonstrate compliance with the NCC, AS 3671, state or local planning conditions, or an acoustic consultant's report. Authorities, certifiers and acoustic consultants may require laboratory test reports or a project-specific assessment.
- Listening examples. The audio is illustrative only. It applies the predicted sound reduction to a generated or uploaded sound and does not model the room. What you hear depends on your device, headphones and volume.
- Your data. All calculations run in your browser. Nothing you enter or upload is sent to AFRC Lab.
- General information only. This calculator is provided for general guidance, as is, without warranty. It is not professional acoustic advice. AFRC Lab Pty Ltd accepts no liability for any loss arising from decisions made using it. For specification, compliance or certification, obtain laboratory test results for the actual product and advice from a qualified acoustic consultant.
Method. No ISO, EN or Australian standard currently sets out how to simulate the sound insulation of a window. These results are simulations: the sound reduction curve (100–5000 Hz, one-third octaves) is predicted by AFRC Lab's model, and Rw, C and Ctr are then calculated from that curve in accordance with AS/NZS ISO 717.1 (ISO 717-1). The model is calibrated against, and checked blind against, laboratory measurements made to ISO 10140 / AS 1191. The results are predictions and are not a substitute for a laboratory test report.
Basis and accuracy. Glazing: mass-law and coincidence model with laminate interlayer damping and a double-leaf model for each cavity, corrected by build class against 105 published laboratory glass curves (leave-one-out Rw error 1.8 dB standard deviation); builds that match a tested build use the measured curve. Window: glazing plus frame plus seal leakage by opening type, calibrated against 210 independent laboratory window tests to ISO 10140 / AS 1191. Blind check with every system family held out of the fit it is tested on: Rw error 2.1 dB rms, 171 of 210 within 2 dB; Rw + Ctr 1.9 dB rms. Repeat laboratory tests of the same window typically read about 1.2 dB apart. Frames are generic: typical widths and surface masses for each frame type and opening type, not a specific product. Seal options marked "estimate" are engineering steps still waiting on test data. Indicative only: not a measurement to AS 1191 / ISO 10140. AFRC Lab acoustic engine v0.6.
Typical results from the calculator
These are simulated ratings from the same engine that runs the calculator above, for a few common glass builds in four opening types. The frame is generic residential aluminium with standard seals. Change any input above to see your own window.
| Glass | Fixed | Awning | Sliding window | Sliding door |
|---|---|---|---|---|
6.38 laminated3/0.38R/3 | 33 (−1; −3)Rw + Ctr 30 | 33 (−1; −3)Rw + Ctr 30 | 31 (0; −2)Rw + Ctr 29 | 32 (−1; −3)Rw + Ctr 29 |
10.38 laminated5/0.38R/5 | 35 (0; −2)Rw + Ctr 33 | 36 (−1; −3)Rw + Ctr 33 | 33 (−1; −3)Rw + Ctr 30 | 34 (−1; −3)Rw + Ctr 31 |
10.5 acoustic laminate5/0.5Q/5 | 37 (−1; −3)Rw + Ctr 34 | 37 (−1; −3)Rw + Ctr 34 | 33 (0; −2)Rw + Ctr 31 | 35 (−1; −3)Rw + Ctr 32 |
IGU 6 / 12 air / 66[12]6 | 34 (−1; −2)Rw + Ctr 32 | 34 (0; −2)Rw + Ctr 32 | 32 (−1; −2)Rw + Ctr 30 | 33 (−1; −2)Rw + Ctr 31 |
IGU 6 / 12 air / 6.76 acoustic6[12]3/0.76Q/3 | 38 (−1; −3)Rw + Ctr 35 | 38 (−1; −3)Rw + Ctr 35 | 34 (−1; −3)Rw + Ctr 31 | 36 (−1; −3)Rw + Ctr 33 |
IGU 12.76 acoustic / 16 argon / 106/0.76Q/6[16ar]10 | 42 (−1; −4)Rw + Ctr 38 | 41 (−1; −3)Rw + Ctr 38 | 34 (0; −2)Rw + Ctr 32 | 37 (−1; −2)Rw + Ctr 35 |
Simulated, not tested. Curves from AFRC Lab's model; Rw, C and Ctr calculated from them to AS/NZS ISO 717.1. AFRC Lab acoustic engine v0.6, run 20 Nov 2026. Rw + Ctr is the traffic-noise number.
What Rw, C and Ctr mean
Rw is the weighted sound reduction index of a building element: a single number, in decibels, worked out from one-third-octave sound reduction values to AS/NZS ISO 717.1. C and Ctr are spectrum adaptation terms. Rw + C suits mid and high-frequency noise such as speech, TV, neighbours and fast traffic. Rw + Ctr suits low-frequency noise such as urban road traffic, slow rail, propeller aircraft and distant jets. For a window facing a road, Rw + Ctr is the number that matters. The calculator shows all three, written as Rw (C; Ctr).
Which number does my project need?
The target comes from your project's acoustic report, planning conditions or state code, not from the base NCC. Common sources: the NSW Transport and Infrastructure SEPP with the interim guideline Development near rail corridors and busy roads; Queensland's QDC MP4.4, buildings in a transport noise corridor, which sets minimum Rw for each component by noise category, with glazing from Rw 35 at category 2 up to Rw 43 at category 4; South Australia's Minister's Building Standard MBS 010; WA State Planning Policy 5.4; Victoria's apartment standards (Clause 58, Standard D16); AS 2021 near airports (ANEF contours); and internal design levels from AS/NZS 2107. Some ask for Rw, some for Rw + Ctr. Your acoustic consultant sets the target; enter it in the calculator's requirement check to see how close a window build gets.
Does double glazing reduce noise?
Yes, but less than most people expect against traffic noise. A standard double-glazed unit has a mass-air-mass resonance in the low frequencies where traffic noise lives, so its Rw + Ctr often improves only a little over a single laminated pane of similar weight. Thicker panes, panes of different thickness, an acoustic interlayer and a wider gap all push the resonance down and lift the result. Compare a single 6.38 laminate with a 6 / 12 / 6 unit in the table above, then try your own builds in the calculator.
Acoustic glass: laminated, acoustic laminate or double glazing
Acoustic glass cuts noise through mass, damping and asymmetry. Heavier glass blocks more sound. Every pane also has a coincidence dip, a frequency where it bends in step with the sound and lets more through; a standard PVB laminate damps that a little, and an acoustic PVB interlayer damps it much more, which is why laminated acoustic glass outperforms plain glass of the same weight. In double glazing, two panes of different thickness dip at different frequencies, so one covers the other's weak spot, and an acoustic laminate as one of the panes gives the best of both. The calculator's glass list covers the common builds, and you can type any build code.
The glass is only part of the window
The opening type and the seals often decide the result. Sliding windows and doors seal with brushes and fins, so more sound leaks around the sashes than through compression-sealed awning and casement windows. In the calculator, the same glass rates 2 to 7 dB lower in a sliding window than in an awning window, and the better the glass, the bigger the gap. The frame matters too:
| Frame | Awning | Sliding window |
|---|---|---|
| Generic aluminium, residential | 36 (−1; −3)Rw + Ctr 33 | 33 (−1; −3)Rw + Ctr 30 |
| Generic aluminium, commercial | 36 (−1; −3)Rw + Ctr 33 | 33 (−1; −3)Rw + Ctr 30 |
| Generic thermally broken aluminium | 34 (−1; −2)Rw + Ctr 32 | 32 (−1; −2)Rw + Ctr 30 |
| Generic uPVC (steel reinforced) | 33 (0; −1)Rw + Ctr 32 | 31 (0; −1)Rw + Ctr 30 |
| Generic timber | 33 (0; −1)Rw + Ctr 32 | 31 (0; −1)Rw + Ctr 30 |
These frames are generic: typical widths and surface masses for each frame type. A real system can rate higher or lower, sometimes by several dB, which is why AFRC Lab models the actual frame, seals and glass for a project.
How accurate is it?
The window model was checked blind against 210 independent laboratory window tests made to ISO 10140 / AS 1191: 171 of 210 came within 2 dB of the measured Rw, with an Rw error of 2.1 dB rms and 1.9 dB rms on Rw + Ctr. In that check every system family was held out of the fit it was tested on. Repeat laboratory tests of the same window typically read about 1.2 dB apart. The glazing model was corrected against 105 published laboratory glass curves (leave-one-out Rw error 1.8 dB standard deviation), and builds that match a tested build use the measured curve. Each result in the calculator shows the accuracy for its opening type. How AFRC Lab checks its other solvers is on the verification page.
Secondary glazing and wide gaps
Secondary glazing and double windows with gaps over about 40 mm are not a calculator option. Their result depends on the cavity, its absorption and how the two frames are connected, so AFRC Lab models them as drawn with a dedicated wide-gap solver. Send us the build.
Your frame isn't generic.
Send us one window and we'll rate your actual system: every frame section, its seals and the glass.
Send us one windowBuild the whole window in BTWAcoustic reports
Window acoustics FAQ
What is an Rw rating?
Rw is the weighted sound reduction index: a single number, in decibels, for how well a building element such as a window blocks airborne sound. It is worked out from one-third-octave sound reduction values using AS/NZS ISO 717.1. The higher the Rw, the less sound gets through.
What does Rw (C; Ctr) mean?
It is the Rw followed by its two spectrum adaptation terms, C and Ctr, which you add to Rw for different kinds of noise. For example, the calculator gives a generic residential aluminium awning window with 10.38 laminated glass, 1500 H x 1200 W, Rw 36 (−1; −3): Rw + C is 35 and Rw + Ctr is 33. C and Ctr are usually negative, so Rw + Ctr is normally the lowest of the three numbers.
Is Rw + Ctr or Rw + C the right number for my window?
For road traffic, slow rail, propeller aircraft and distant jets, use Rw + Ctr, because that noise is heavy in low frequencies. For speech, neighbours, TV and fast traffic, use Rw + C. If the window faces a road, Rw + Ctr is usually the number your acoustic report asks for.
What is a good Rw rating for a window?
It depends on how loud it is outside and what the room is for, so the right target is the one in your project's acoustic report or planning conditions. As a reference point, Queensland's QDC MP4.4 sets minimum glazing ratings in transport noise corridors from Rw 35 (noise category 2) to Rw 43 (category 4). Use the calculator's requirement check to see which builds get close.
Does double glazing reduce noise?
Yes, but often less than people expect against traffic noise. A standard double-glazed unit has a mass-air-mass resonance in the low frequencies where traffic noise sits, so its Rw + Ctr can be only a little better than a single laminated pane. Thicker, unequal panes, an acoustic interlayer and a wider gap all help; compare a single 6.38 laminate with a 6 / 12 / 6 unit in the calculator.
Is acoustic glass better than double glazing?
For traffic noise, a thick acoustic laminate often matches or beats a standard double-glazed unit. The best of both is a double-glazed unit with an acoustic laminate as one pane. Try both builds in the calculator with your window type and size.
Do acoustic windows work?
Yes, when the glass, the seals and the opening type are chosen together. A high-performing pane in a leaky slider underperforms: in the calculator the same glass rates 2 to 7 dB lower in a sliding window than in an awning window. The weakest path through the window sets the result.
How soundproof can a window get?
No window is soundproof: every window reduces sound by a number of decibels rather than stopping it. A reduction of about 10 dB is heard as roughly half as loud. The calculator shows how far each change moves the rating, and which path (glass, frame or seals) is letting the most noise through.
Does window size change the acoustic rating?
Yes. Panel size shifts the low-frequency behaviour of the glass and changes how much frame and seal there is per square metre of window, which is why the calculator asks for the size as H x W.
Is Rw the same as STC?
They are similar ideas from different standards and are not interchangeable. STC (ASTM E413) is the US rating; Rw (ISO 717-1, adopted in Australia as AS/NZS ISO 717.1) is the Australian and European one. The numbers are often close but are worked out with different curves and frequency ranges.
Is this a test report? Can I use it for compliance?
No. It is a simulated screening result for a window with a generic frame, not a laboratory test. For a project, AFRC Lab models your actual system and issues a report, and your acoustic consultant confirms the requirement.
What is acoustic glazing?
Acoustic glazing is glass built to cut noise. It is usually heavier, laminated with an acoustic interlayer that damps vibration, and in double glazing often uses two panes of different thickness so they don't resonate at the same frequency.